-44 %
Brand: FlyRobo
SKU: 1593
A handy Piezo buzzer for use as an audio warning when activating and deactivating the board and also serves as a warning for low voltage in flight. It is used for KK2 KK2.1 & Naze32 Flight Controller.
Features:
Plug: JST Female
Voltage: 3.7-5V
Wire Length: 110mm
Package Includes:
..
₹111 ₹199
-31 %
Out Of Stock
Brand: FlyRobo
SKU: 2462
Mini CC3D V Type Receiver Antenna Fixing Seat Mount Holder Pedestal, this antenna will stand V-style, and ensure you get the better signal. Antenna fixing base mount can make your antenna fixed with double-sided adhesive tape at any place on the machine.
Features:
V type Antenna
Color: Bl..
₹89 ₹129
-48 %
Brand: FlyRobo
SKU: 1460
MT60 3 Pole Motor / ESC Connector set is the perfect solution for securing your brushless motor / ESC connections.
The connector set features male and female connectors which are both fitted with 3.5mm bullets and supplied with a cable tidy attachment to keep things nice and neat.
The connect..
₹104 ₹199
-32 %
Out Of Stock
Brand: FlyRobo
SKU: 1581
PDB-XT60 has been engineered to provide the highest possible performance and reliability in a 36x50mm & 4 layers PCB. It distributes power from a LiPo pack to 6 ESCs, as well as providing synchronized & regulated DC 5V outputs & linear regulated DC 12V for powering Cameras, Servos, RC receivers, Fli..
₹299 ₹439
-27 %
Brand: FlyRobo
SKU: 2340
Pitot tube for the Arduplane Airspeed Sensor for pixhawk, APM 2.5 and 2.6
Package Includes:-
1 X Pitot Tube..
₹437 ₹599
-54 %
Out Of Stock
Brand: FlyRobo
SKU: 2015
Pixhawk 0.96inch OLED Onboard Display Module is suitable for Pixhawk flight controller and can be useful for displaying a small amount of vehicle information before takeoff.
This information includes on Display:
Arming failure messages
Flight mode
Battery voltage
GPS Lock and satellit..
₹321 ₹699
Out Of Stock
Brand: FlyRobo
SKU: 266
Specifications and Features:
Package Weight: 5 gm
Number of Ports: 5.
Board Dimensions: 33 x 12 x 6 mm(LxWxH)
Net Weight: 3g
Brand new and high quality
The I2C splitter expands the I2C port to allow up to four additional peripherals to connect to Pixhawk.
Use the 4-wire cable to c..
₹194
Out Of Stock
Brand: FlyRobo
SKU: 1604
The Mavlink LED Controller includes a controller board, 6 sets of highlight LED strips and one USB to UART module. It is compatible with any flight controller with ardupilot or PX4 firmware like Pixhawk serial, APM serial, Pixracer, NAVIO2, PXFmini, etc. It is compatible with Mavlink 1 and Mavlink 2..
₹2,051
-12 %
Out Of Stock
Brand: FlyRobo
SKU: 1584
Pixhawk Passive Buzzer has a two-position JST-SH connector on one side that plugs directly into the Pixhawk. Once connected you will be able to hear different sounds that relate to different modes!
This also includes the PX4 safety switch to enable you to arm/disarm your board at a moment's notic..
₹528 ₹599
-39 %
Brand: FlyRobo
SKU: 1597
This is a 30cm replacement GPS/Compass Connection Cable for modules like the Ublox M8N. It comes with a 6P connector for use with the Pixhawk . It is suitable for Pixhawk PX4 Flight Controller.
Package Includes:
1 x Pixhawk PX4 Flight Controller GPS Connection Cable 6 Pin
..
₹181 ₹299
-13 %
Brand: FlyRobo
SKU: 1589
This includes an external RGB-LED and USB receptacle to connect to Pixhawk. Use the provided cables and connect to the I2C splitter module to set up a bright, multicolor LED and convenient USB port for your vehicle.
Features:
RGB indicator extends to outside displaying
Extension USB inter..
₹685 ₹789
-34 %
Out Of Stock
Brand: FlyRobo
SKU: 1583
It is a plastic case for Pixhawk PX4 Autopilot PIX 2.4.8 Pixhawk 2.4.8 Flight Controller. It provides good protection to your flight controller.
Package Includes:
1 x Plastic Case Cover Shell for Pixhawk..
₹593 ₹899
