Menu
Your Cart

Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit

Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit - Flight Controller - Multirotor
Pixhawk PX4 Autopilot 2.4.8 32 Bit Flight Controller kit
₹9,499

(inc GST)

  • Stock: In Stock
  • With this product you will receive ₹95 FlyRobo Cashback.
  • SKU: FRC-02-805
7 Day Return
Get 7 Day Replacement/Refund on this product
Free shipping
Get free shipping on this product. Buy above ₹ 999 and get free shipping.
COD Available
Get this product with Cash at the time of Delivery
Support
Get best after-sale support From our Technical team with different Tutorials

Features:
 
1. The advanced 32-bit ARM CortexM4 high-performance processors can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
 
Specifications:
 
Microprocessor
 
1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit
2. frequency: 168MHZ, 256K RAM
3.32 STM32F103 backup coprocessor
 
Sensor
 
1.L3GD20 3-axis digital gyroscope 16
2.LSM303D 3-axis accelerometer 14 / Magnetometer
3.MPU6000 6-axis accelerometer / magnetometer
4.MS5611 precision barometer
 
Interface
 
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
 
 
Power module :

The APM 2.6 Power Module is a simple way of providing your APM 2.6 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 6S LiPo battery. The Power Module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection.

Note: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power servos. Use your aircraft\'s own ESC/BEC for that.

Specifications:

Max input voltage: 28V

Max current sensing: 90A

Voltage and current measurement configured for 5V ADC

Switching regulator outputs 5.3V and 3A max  

6-pos DF13 cable plugs directly to APM 2.5\'s \'PM\' connector

        

 

Packing list:
 
Pixhawk 2.4.8  32bit ARM Flight Controller x 1
Safety button x 1
Buzzer x 1
Micro SD TF card  x1
M7N GPS with GPS holder× 1
Cables
power module x 1
 

 
 
NOTE: Before connect with the computer, you need to insert the SD card first , then flash the program, otherwise the LED indicator will not light up.
Please make sure you read these before you use.

 
 

 


    Write a review

    Note: HTML is not translated!
    Bad Good

    The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

    Name
    Email
    Phone
    Comments